119
8018P–AVR–08/10
ATmega169P
The timing diagram for the CTC mode is shown in Figure 15-6. The counter value (TCNT1)
increases until a compare match occurs with either OCR1A or ICR1, and then counter (TCNT1)
is cleared.
Figure 15-6. CTC Mode, Timing Diagram
An interrupt can be generated at each time the counter value reaches the TOP value by either
using the OCF1A or ICF1 Flag according to the register used to define the TOP value. If the
interrupt is enabled, the interrupt handler routine can be used for updating the TOP value. How-
ever, changing the TOP to a value close to BOTTOM when the counter is running with none or a
low prescaler value must be done with care since the CTC mode does not have the double buff-
ering feature. If the new value written to OCR1A or ICR1 is lower than the current value of
TCNT1, the counter will miss the compare match. The counter will then have to count to its max-
imum value (0xFFFF) and wrap around starting at 0x0000 before the compare match can occur.
In many cases this feature is not desirable. An alternative will then be to use the fast PWM mode
using OCR1A for defining TOP (WGM13:0 = 15) since the OCR1A then will be double buffered.
For generating a waveform output in CTC mode, the OC1A output can be set to toggle its logical
level on each compare match by setting the Compare Output mode bits to toggle mode
(COM1A1:0 = 1). The OC1A value will not be visible on the port pin unless the data direction for
the pin is set to output (DDR_OC1A = 1). The waveform generated will have a maximum fre-
quency of f
OC1A = fclk_I/O/2 when OCR1A is set to zero (0x0000). The waveform frequency is
defined by the following equation:
The N variable represents the prescaler factor (1, 8, 64, 256, or 1024).
As for the Normal mode of operation, the TOV1 Flag is set in the same timer clock cycle that the
counter counts from MAX to 0x0000.
TCNTn
OCnA
(Toggle)
OCnA Interrupt Flag Set
or ICFn Interrupt Flag Set
(Interrupt on TOP)
1
4
Period
2
3
(COMnA1:0 = 1)
fOCnA
f
clk_I/O
2
N
1
OCRnA
+
()
---------------------------------------------------
=
相关PDF资料
ATMEGA169P-16MCU MCU AVR 16K ISP FLSH 16MHZ 64QFN
AT91SAM7XC256-CU MCU ARM 256K HS FLASH 100-TFBGA
PIC16LF874A-I/P IC MCU FLASH 4KX14 EE A/D 40DIP
PIC16F84-10/SO IC MCU FLASH 1KX14 EE 18SOIC
AT91SAM7XC128-CU MCU ARM 128K HS FLASH 100-TFBGA
PIC18F2458-I/SO IC PIC MCU FLASH 12KX16 28SOIC
PIC18F4455-I/P IC PIC MCU FLASH 12KX16 40DIP
AT91SAM7X256-CU MCU ARM 256K HS FLASH 100-TFBGA
相关代理商/技术参数
ATMEGA169PV-8MU 功能描述:8位微控制器 -MCU AVR 16K FLASH 512B EE 1K SRAM 5V RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
ATMEGA169PV-8MU SL383 制造商:Atmel Corporation 功能描述:MCU 8BIT ATMEGA RISC 16KB FLASH 2.5V/3.3V/5V 64PIN MLF - Tape and Reel
ATMEGA169PV-8MU 制造商:Atmel Corporation 功能描述:IC 8BIT MCU AVR MEGA 8MHZ 64-QFN
ATMEGA169PV-8MUR 功能描述:8位微控制器 -MCU AVR LCD 16KB FLSH EE 512B 1KB SRAM-8MHZ RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
ATMEGA169V 制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:8-bit Microcontroller with 16K Bytes In-System Programmable Flash
ATMEGA169V_06 制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:8-bit Microcontroller with 16K Bytes In-System Programmable Flash
ATMEGA169V-1AC 功能描述:IC MCU 8BIT 16KB FLASH 64TQFP 制造商:microchip technology 系列:AVR? ATmega 包装:托盘 零件状态:停產 核心处理器:AVR 核心尺寸:8-位 速度:1MHz 连接性:SPI,UART/USART,USI 外设:欠压检测/复位,LCD,POR,PWM,WDT I/O 数:53 程序存储容量:16KB(8K x 16) 程序存储器类型:闪存 EEPROM 容量:512 x 8 RAM 容量:1K x 8 电压 - 电源(Vcc/Vdd):1.8 V ~ 5.5 V 数据转换器:A/D 8x10b 振荡器类型:内部 工作温度:0°C ~ 70°C 封装/外壳:64-TQFP 供应商器件封装:64-TQFP(14x14) 基本零件编号:ATmega169 标准包装:160
ATMEGA169V-1AI 制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:8-bit AVR Microcontroller with 16K Bytes In-System Programmable Flash